Select Page
Search
Generic filters
Exact matches only

Rail

In rail vehicle construction, the scope for bonding ranges from large front modules through glazing to smaller interior components. This industry meets the highest safety standards and therefore places the highest demands on materials and processes. The proof of fire properties for materials and material composites is defined by the industry-specific standard EN 45545-2.
Depending on the safety requirements, the use of materials is tied to an extended scope of qualification. We offer products that have extended certificates or are already qualified by OEMs and large railway operators.

Fire-retardant structural adhesives for rail vehicles

In addition to the elastic adhesives, various structural adhesives are available which have been tested according to EN 45545-2. These products are mostly used for bondings with low safety requirements (e.g. for smaller interior components).

Glass bonding for rail vehicles

In addition to new glazing at the OEM, the replacement of panes in the event of repairs is an important economic factor for railway operators. Short repair and departure times due to rapid curing are required. 1- and 2-component adhesives are also available as cartridges for mobile use. Some of the materials are qualified by OEMs and large railway operators and tested according to EN45545-2.

Joint sealing & joint filling for rail vehicles

In addition to bonding, joint sealing is an important factor in rail vehicles to prevent the penetration of water and corrosion. The joint materials are easy to smooth for a visually appealing joint. They have been tested for their resistance to railway-specific media (e.g. cleaning agents). The materials are partly qualified by OEMs and large railway operators and tested according to EN45545-2.

Materials for the electrical casting of rail vehicles

Rail vehicles have a large number of electronic components for the drive and in the systems. Electronic components are usually protected by embedding them in special casting resins. We offer a wide range of casting resins tested to EN 45545-2.

Structural bonding of exterior components & interior of rail vehicles

On the outside, GFK structures are glued to the steel wagon box. Due to the component size and different material properties, the adhesive joint must be elastic but high-strength. 1- and 2-component polyurethane adhesives are used. The two-component technology ensures the curing of large adhesive beads without additional humidity. Some of the materials are qualified by OEMs and large railway operators and tested according to EN45545-2.

Surface pretreatment for rail vehicles

A clean and grease-free surface is necessary to ensure a high-strength, durable bond. Surfaces are treated with suitable cleaners. In some cases additional primers are used to increase the adhesive strength and long-term durability. The products (cleaners, primers, adhesives) are matched to each other and the material combinations are partly qualified by railway OEMs and large railway operators.

Fire-retardant structural adhesives for rail vehicles

In addition to the elastic adhesives, various structural adhesives are available which have been tested according to EN 45545-2. These products are mostly used for bondings with low safety requirements (e.g. for smaller interior components).

Glass bonding for rail vehicles

In addition to new glazing at the OEM, the replacement of panes in the event of repairs is an important economic factor for railway operators. Short repair and departure times due to rapid curing are required. 1- and 2-component adhesives are also available as cartridges for mobile use. Some of the materials are qualified by OEMs and large railway operators and tested according to EN45545-2.

Joint sealing & joint filling for rail vehicles

In addition to bonding, joint sealing is an important factor in rail vehicles to prevent the penetration of water and corrosion. The joint materials are easy to smooth for a visually appealing joint. They have been tested for their resistance to railway-specific media (e.g. cleaning agents). The materials are partly qualified by OEMs and large railway operators and tested according to EN45545-2.

Materials for the electrical casting of rail vehicles

Rail vehicles have a large number of electronic components for the drive and in the systems. Electronic components are usually protected by embedding them in special casting resins. We offer a wide range of casting resins tested to EN 45545-2.

Structural bonding of exterior components & interior of rail vehicles

On the outside, GFK structures are glued to the steel wagon box. Due to the component size and different material properties, the adhesive joint must be elastic but high-strength. 1- and 2-component polyurethane adhesives are used. The two-component technology ensures the curing of large adhesive beads without additional humidity. Some of the materials are qualified by OEMs and large railway operators and tested according to EN45545-2.

Surface pretreatment for rail vehicles

A clean and grease-free surface is necessary to ensure a high-strength, durable bond. Surfaces are treated with suitable cleaners. In some cases additional primers are used to increase the adhesive strength and long-term durability. The products (cleaners, primers, adhesives) are matched to each other and the material combinations are partly qualified by railway OEMs and large railway operators.

Agomet® 2-component methyl methacrylate adhesives

Developed for processing with hardener powder or hardener paste to ensure easy mixing.

Araldite® 2-component epoxy casting resins

Unfilled and filled, cold and hot-curing epoxy resin-based casting compounds for atmospheric or vacuum casting with a wide range of properties.

Araldite® 2-component epoxy casting resins

For all industrial applications, from electronics to mold making. The portfolio includes products ranging from particularly low shrinkage for high-precision castings to products resistant to high temperatures and chemicals and materials with excellent insulation properties for electrical engineering applications.

Araldite® 2-component epoxy resin adhesives

Depending on the type, they can be used for structural bonding of metals, thermosets and reinforced plastics. Can have very high strength and temperature resistance (up to 210°C).

Araldite® 2-component epoxy resins

For almost all applications in industry and trade, where high-strength and permanently resistant adhesive bonds of the most diverse substrates are required.

Araldite® 2-component epoxy trickle resins

Trickle resins with very good electrical properties, high mechanical strength and heat form stability, suitable for high operating temperatures.

Araldite® 2-component methyl methacrylate adhesives

For all high-strength yet tough elastic adhesive joints. Very high tolerance to poorly bondable substrates or surfaces that are not optimally prepared.

Araldite® 2-component polyurethane adhesives

For flexible to high-strength, for fast to slow bonding of a large number of substrates.

Araldite® 2-component polyurethane casting resins

For all industrial applications, from electronics to mold making. Available in a high variety of types, whereby a particularly fine adjustment to the requirements of the application is realizable.

Araldite® / Aradur® Formulated resin / hardener systems

High-performance resin systems for all industrial applications, available in various varieties for all common manufacturing processes.

Araldite® Color pastes

Allow the product color to be adapted to customer requirements with light-colored potting or laminating resin systems.

Araldite® Epoxy impregnating resins for casting

Epoxy resin systems for impregnation of windings in classical atmospheric or vacuum casting.

Araldite® Epoxy impregnating resins for dip impregnation

Epoxy resins with particularly high storage stability in immersion baths for use in impregnating baths, with high glass transition, suitable for high and operating temperatures.

Araldite® Fillers

Allow the individual adaptation of unfilled resin systems to the requirements of the user.

Araldite® Flame retardant epoxy adhesives

Flame retardant 2-component adhesives with classified fire performance according to UL94 and EN 45545-2 standards.

Araldite® Laminating resins

Epoxy laminating resins for component production and mold making, especially proven in vehicle construction, racing and sports equipment construction, aerospace, transportation and marine, wind power, electronics and medical technology.

Araldite® Phenolic polycondensation adhesives

Are 1-component and are used for bonding metal or friction linings. High temperatures and pressures are required for hardening.

Araldite® Thermally conductive epoxy adhesives

2-component adhesives with higher thermal conductivity values for improved heat transfer of components.

Arathane® 2-component polyurethane casting resins

Potting compounds with very good processing properties, for very flexible to hard moulding materials with good temperature stability up to thermal class F, thermally conductive, UL94.

Aratherm® High thermally conductive epoxy casting resins

Hot-curing 1-component epoxy resin systems with very high thermal conductivity.

BETABRADE™ Contamination and silicone remover

For removing silicone contamination from glass panes or ceramic screen printing without scratching the glass surface.

BETACLEAN™ Surface cleaners

Cleaner for the removal of dirt such as dust, grease and oil from adhesive surfaces. Depending on the application, cleaners are available for use on metals, plastics, glass and other substrates.

BETAFILL™ 1-component polyurethane sealants

Air humidity curing, adhesive, paintable, elastic adhere and sealing compounds based on 1-component polyurethane for sealing, filling and sealing in vehicle and container construction.

BETAFILL™ Polyurethane sealants

Air humidity curing, overpaintable, elastic adhesive and sealing compounds based on 1-component polyurethane for sealing, filling and sealing in vehicle construction.

BETAFORCE™ 2-component polyurethane structural adhesives, high modulus

Room temperature fast curing 2-component polyurethane adhesive with high mechanical strength and high elongation at break, specially developed for structural bonding.

BETAGUARD™ Rubber-based sealants, relining adhesives

Rubber-based, expandable sealing and relining adhesives with low strength. To prevent vibrations by compensating for tolerances and sheet spacings in the carcass.

BETALINK™ 1-component polyurethane semi-structural adhesives

High adhere, elastic and air humidity-curing adhesive and sealing compounds based on 1-component polyurethane. Approved by Technical Inspection Agency for the bonding of aerodynamic attachments in vehicle construction.

BETAMATE™ 1-component polyurethane structural adhesives

Air humidity curing 1-component polyurethane adhesives and sealants for high-strength, permanently elastic adhesive joints with accelerated curing.

BETAMATE™ 2-component epoxy resin adhesives

For crash-resistant structural bonding of repair sheets and metals in general as well as fiber-reinforced plastics. Achieves approximately the strength of 1K epoxy resin adhesives.

BETAMATE™ 2-component polyurethane structural adhesives

2-component polyurethane adhesive for direct glazing which harden quickly at room temperature. Suitable for bonding metals, plastics and composites, provided that appropriate pre-treatment has been applied.

BETAPRIME™ Primer

Film-forming glass, plastic and metal primers which, in addition to the adhesion promoter, also increase the UV and corrosion protection of an adhesive bond.

BETASEAL™ 1-component polyurethane adhesives for direct glazing

Highly viscous, air-humidity-curing 1-component polyurethane adhesive and sealing compounds for direct glazing in vehicle construction with diverse type-dependent properties.

BETASEAL™ 2-component polyurethane adhesives for direct glazing

2-component, non-conductive, high-modulus, highly viscous, chemically curing polyurethane adhesives and sealants for high-strength, permanently elastic adhesive joints of glass.

BETAWIPE™ Activators

Activators which increase the adhesion and ageing resistance of certain substrates such as glass or aluminium by creating chemical bonds between substrate and primer.

Bluesil™ 2-component silicone casting compounds

For all areas of mold making where highly flexible molding compounds have to be used.

Bluesil™ 2-component silicones

2-component silicone casting compounds, optically clear or containing filler for higher heat dissipation.

Bluesil™ Silicone gels

2-component silicones with gel-like end properties, extremely low hardness and extremely low elasticity modulus, optically clear.

CAF® 1-component silicone adhesives

Room temperature crosslinking adhesives and sealants for industry and trade, maintenance and repair, high-performance applications with high temperature resistance, protection and coating of electronic assemblies with castable products.

CAF® 2-component silicone adhesives

Through special activation, they enable a hardening process without condensation products (e.g. acetic acid) even in closed joints without access to humidity and offer particularly fast hardening.

Cinquasia® Organic pigment powder

Organic pigments with excellent light fastness and high chemical and solvent resistance.

Euromelt® 2-component polyamide hotmelt casting compounds

1-component co-polyamides for a wide operating temperature range and low viscosity for very good flow behavior with only low potting pressure.

Euvinyl® Pigments in PVC carrier

Irgafos additives are secondary antioxidants that act as peroxy radical scavengers during plastics processing.

Glacier Mica-based interference pigments

Titanium-coated synthetic mica for producing white sparkling effects with bluish frost character.

Heliogen® Organic pigment powder

Organic pigments with excellent light fastness and high chemical and solvent resistance.

Irgaclear® Clarifier nucleating agents

Characterized in particular in the application in polypropylene, by the transparency of the polymer is significantly increased.

Irgafos® Phosphite process stabilizers

Irgafos additives are secondary antioxidants that act as peroxy radical scavengers during plastics processing.

Irgalite® Organic pigment powder

Organic pigments with excellent light fastness and high chemical and solvent resistance.

Irgazin® Organic pigment powder

Organic pigments with excellent light fastness and high chemical and solvent resistance.

L&L Hybrid sealants

Primerless UV-stable adhesive and sealing systems on hybrid basis with strong adhesion to metal, composites, thermoplastics with a broad mechanical spectrum.

L&L Seal 1-component silane-modified polymer adhesives

Primerless systems with good adhesion to metals, composites and plastics. Solvent- and isocyanate-free, with good UV resistance and low shrinkage for low marking.

Lumina® Mica-based interference pigments

Titanium-coated synthetic mica for producing white sparkling effects with bluish frost character.

MagnaPearl® Pearlescence pigments

Pearlescence pigments based on oxide-coated natural mica. Different particle sizes and oxide layer thicknesses give the pigments the different semi-transparent sparkling effects in different metallic and colored shades.

Pactan® 1-component silicones

Neutral-curing 1-component silicones with very good adhesion properties for potting and sealing electrical components.

Paliogen® Organic pigment powder

Organic pigments with excellent light fastness and high chemical and solvent resistance.

Paliotol® Organic pigment powder

Organic pigments with excellent light fastness and high chemical and solvent resistance.

Permabond® Anaerobic adhesives

1-component, solvent-free systems that harden in the absence of atmospheric oxygen and the presence of metal surfaces (ferrous and non-ferrous metals). The liquid anaerobic adhesive fills the gap between the contact surfaces and hardens to a solid acrylic.

RenCast® 2-component epoxy casting resins

For the production of high-precision castings in model and mold making. Products with excellent resistance to high temperatures are available.

RenCast® 2-component polyurethane fast casting resins

For the production of control or auxiliary castings in model and mold making.

RenGel™ Epoxy gelcoats and coupling layers

For all applications in model and mold making, specially adapted to temperature requirements, abrasion resistance, grindability, polishability and high chemical resistance.

RenLam® Laminating resins

Epoxy laminating resins with focus on mould and tool making.

RenLease® Release agents

For easy demolding of components made of polyurethane or epoxy resins.

RenPim™ 2-component polyurethane casting resins

For component production in rapid prototyping. Suitable for vacuum casting.

Rhodorsil® 2-component silicone casting compounds

For all areas of mold making where highly flexible molding compounds have to be used.

RickoStab Multi-component additive packages

The combination of several additives, e.g. primary and secondary antioxidants, HALS and UV absorbers facilitate dosage during processing.

Thermally conductive silicones

2-component silicone casting compounds, gels and gap fillers with excellent thermal conductivity.

UREOL® Adhesives for epoxy tooling boards

Color, density, coefficient of thermal expansion and glass transition point are specially matched to the mechanical properties of Ureol epoxy resin boards.

UREOL® Adhesives for polyurethane tooling boards

Color, density, coefficient of thermal expansion and glass transition point are specially matched to the mechanical properties of Ureol polyurethane boards.

UREOL® Epoxy tooling boards

Optimally matched to the requirements of composite mold making. Particularly suitable for all mold making applications in the temperature range up to 140°C, especially for prepreg laying tools.

Wax sheets

For the simulation of the component wall thickness in mould construction.

Bodo Möller Chemie

Events

JEC World 2020

03.03.2020, Paris

Bonding Seminar 2020

14.05.2020, Augsburg

News

The specialty chemicals expert distributes innovative Loctite products for electrical and electronics applications

Comprehensive ISO-certified production with growing capacity for epoxy resins, polyurethanes and packaging fillers