Select Page
Search
Generic filters
Exact matches only

Bus & Truck

The production of commercial vehicles is characterised by technically and economically demanding processes. The demand for low vehicle weight leads to a material mix that makes thermal joining processes increasingly difficult. GRP add-on parts are bonded to the vehicle structure and are playing an increasingly important role in body-in-white and final assembly. Attachments are joined together structurally or elastically and the vehicle is sealed at the same time.

Fire retardant structural adhesives for commercial transportation

Production of commercial vehicles sometimes places increased demands on the fire properties of the materials. Adhesives are used which are self-extinguishing, have a low heat release and produce few toxic fumes.

Glass bonding for commerical transportation

Elastic adhesives are used for window pane bonding. High elasticity and low stiffness prevent the transition of stress peaks and thus tearing of the pane, e.g. in the case of twisted car bodies. High adhesive strengths integrate the panes as load-bearing elements in the structure of buses and driver's cabs.

Joint sealing, joint filling & underbody protection for commerical transporation

In addition to bonding, seam sealing is an important function of an adhesive and sealant. The penetration of water into gaps and cavities as well as the resulting corrosion are prevented. Depending on the application, different types of materials are used.

Structural bonding in the construction of commercial transportation

Structural adhesives are increasingly being used in carcass construction. Due to the full-surface connection of the components, sheet thicknesses can be reduced and weight saved. The adhesives cure at room temperature (two-component) or in a KTL furnace (one component).

Structural bonding of exterior and interior components for commerical transporation

A variety of different materials (e.g. plastics, composites, metals, glass) are used for add-on and interior parts. Special requirements arise from the combination of materials. The adhesive must build up good adhesion to the materials to be bonded, differences in thermal expansion are compensated by the adhesive and the adhesive joint.

Surface pretreatment for commercial transportation

A clean and grease-free surface is necessary to ensure a high-strength, durable bond. Surfaces are treated with suitable cleaners. In some cases additional primers are used to increase the adhesive strength and long-term durability. The products (cleaners, primers, adhesives) are matched to each other and the process reliability is proven.

Fire retardant structural adhesives for commercial transportation

Production of commercial vehicles sometimes places increased demands on the fire properties of the materials. Adhesives are used which are self-extinguishing, have a low heat release and produce few toxic fumes.

Glass bonding for commerical transportation

Elastic adhesives are used for window pane bonding. High elasticity and low stiffness prevent the transition of stress peaks and thus tearing of the pane, e.g. in the case of twisted car bodies. High adhesive strengths integrate the panes as load-bearing elements in the structure of buses and driver's cabs.

Joint sealing, joint filling & underbody protection for commerical transporation

In addition to bonding, seam sealing is an important function of an adhesive and sealant. The penetration of water into gaps and cavities as well as the resulting corrosion are prevented. Depending on the application, different types of materials are used.

Structural bonding in the construction of commercial transportation

Structural adhesives are increasingly being used in carcass construction. Due to the full-surface connection of the components, sheet thicknesses can be reduced and weight saved. The adhesives cure at room temperature (two-component) or in a KTL furnace (one component).

Structural bonding of exterior and interior components for commerical transporation

A variety of different materials (e.g. plastics, composites, metals, glass) are used for add-on and interior parts. Special requirements arise from the combination of materials. The adhesive must build up good adhesion to the materials to be bonded, differences in thermal expansion are compensated by the adhesive and the adhesive joint.

Surface pretreatment for commercial transportation

A clean and grease-free surface is necessary to ensure a high-strength, durable bond. Surfaces are treated with suitable cleaners. In some cases additional primers are used to increase the adhesive strength and long-term durability. The products (cleaners, primers, adhesives) are matched to each other and the process reliability is proven.

Agomet® 2-component methyl methacrylate adhesives

Developed for processing with hardener powder or hardener paste to ensure easy mixing.

Araldite® 2-component epoxy casting resins

Unfilled and filled, cold and hot-curing epoxy resin-based casting compounds for atmospheric or vacuum casting with a wide range of properties.

Araldite® 2-component epoxy casting resins

For all industrial applications, from electronics to mold making. The portfolio includes products ranging from particularly low shrinkage for high-precision castings to products resistant to high temperatures and chemicals and materials with excellent insulation properties for electrical engineering applications.

Araldite® 2-component epoxy resin adhesives

Depending on the type, they can be used for structural bonding of metals, thermosets and reinforced plastics. Can have very high strength and temperature resistance (up to 210°C).

Araldite® 2-component epoxy resins

For almost all applications in industry and trade, where high-strength and permanently resistant adhesive bonds of the most diverse substrates are required.

Araldite® 2-component epoxy trickle resins

Trickle resins with very good electrical properties, high mechanical strength and heat form stability, suitable for high operating temperatures.

Araldite® 2-component methyl methacrylate adhesives

For all high-strength yet tough elastic adhesive joints. Very high tolerance to poorly bondable substrates or surfaces that are not optimally prepared.

Araldite® 2-component polyurethane adhesives

For flexible to high-strength, for fast to slow bonding of a large number of substrates.

Araldite® 2-component polyurethane casting resins

For all industrial applications, from electronics to mold making. Available in a high variety of types, whereby a particularly fine adjustment to the requirements of the application is realizable.

Araldite® / Aradur® Formulated resin / hardener systems

High-performance resin systems for all industrial applications, available in various varieties for all common manufacturing processes.

Araldite® Color pastes

Allow the product color to be adapted to customer requirements with light-colored potting or laminating resin systems.

Araldite® Epoxy impregnating resins for casting

Epoxy resin systems for impregnation of windings in classical atmospheric or vacuum casting.

Araldite® Epoxy impregnating resins for dip impregnation

Epoxy resins with particularly high storage stability in immersion baths for use in impregnating baths, with high glass transition, suitable for high and operating temperatures.

Araldite® Fillers

Allow the individual adaptation of unfilled resin systems to the requirements of the user.

Araldite® Flame retardant epoxy adhesives

Flame retardant 2-component adhesives with classified fire performance according to UL94 and EN 45545-2 standards.

Araldite® Laminating resins

Epoxy laminating resins for component production and mold making, especially proven in vehicle construction, racing and sports equipment construction, aerospace, transportation and marine, wind power, electronics and medical technology.

Araldite® Phenolic polycondensation adhesives

Are 1-component and are used for bonding metal or friction linings. High temperatures and pressures are required for hardening.

Araldite® Thermally conductive epoxy adhesives

2-component adhesives with higher thermal conductivity values for improved heat transfer of components.

Arathane® 2-component polyurethane casting resins

Potting compounds with very good processing properties, for very flexible to hard moulding materials with good temperature stability up to thermal class F, thermally conductive, UL94.

Aratherm® High thermally conductive epoxy casting resins

Hot-curing 1-component epoxy resin systems with very high thermal conductivity.

BETABRADE™ Contamination and silicone remover

For removing silicone contamination from glass panes or ceramic screen printing without scratching the glass surface.

BETACLEAN™ Surface cleaners

Cleaner for the removal of dirt such as dust, grease and oil from adhesive surfaces. Depending on the application, cleaners are available for use on metals, plastics, glass and other substrates.

BETAFILL™ 1-component polyurethane sealants

Air humidity curing, adhesive, paintable, elastic adhere and sealing compounds based on 1-component polyurethane for sealing, filling and sealing in vehicle and container construction.

BETAFILL™ Polyurethane sealants

Air humidity curing, overpaintable, elastic adhesive and sealing compounds based on 1-component polyurethane for sealing, filling and sealing in vehicle construction.

BETAFORCE™ 2-component polyurethane structural adhesives, high modulus

Room temperature fast curing 2-component polyurethane adhesive with high mechanical strength and high elongation at break, specially developed for structural bonding.

BETAGUARD™ Rubber-based sealants, relining adhesives

Rubber-based, expandable sealing and relining adhesives with low strength. To prevent vibrations by compensating for tolerances and sheet spacings in the carcass.

BETALINK™ 1-component polyurethane semi-structural adhesives

High adhere, elastic and air humidity-curing adhesive and sealing compounds based on 1-component polyurethane. Approved by Technical Inspection Agency for the bonding of aerodynamic attachments in vehicle construction.

BETAMATE™ 1-component epoxy resin adhesives

Specially developed for use in automotive shell construction to increase crash stability and stiffness. They adhere excellently to the oiled steel and aluminium grades used.

BETAMATE™ 1-component polyurethane structural adhesives

Air humidity curing 1-component polyurethane adhesives and sealants for high-strength, permanently elastic adhesive joints with accelerated curing.

BETAMATE™ 1-component silane-modified polymer adhesives

1-component air humidity curing sealant based on hybrid polymer with permanent elasticity. Scentless, with low shrinkage, good UV stability and good primerless adhesion on many substrates.

BETAMATE™ 2-component epoxy resin adhesives

For crash-resistant structural bonding of repair sheets and metals in general as well as fiber-reinforced plastics. Achieves approximately the strength of 1K epoxy resin adhesives.

BETAMATE™ 2-component polyurethane structural adhesives

2-component polyurethane adhesive for direct glazing which harden quickly at room temperature. Suitable for bonding metals, plastics and composites, provided that appropriate pre-treatment has been applied.

BETAPRIME™ Primer

Film-forming glass, plastic and metal primers which, in addition to the adhesion promoter, also increase the UV and corrosion protection of an adhesive bond.

BETASEAL™ 1-component polyurethane adhesives for direct glazing

Highly viscous, air-humidity-curing 1-component polyurethane adhesive and sealing compounds for direct glazing in vehicle construction with diverse type-dependent properties.

BETASEAL™ 2-component polyurethane adhesives for direct glazing

2-component, non-conductive, high-modulus, highly viscous, chemically curing polyurethane adhesives and sealants for high-strength, permanently elastic adhesive joints of glass.

BETAWIPE™ Activators

Activators which increase the adhesion and ageing resistance of certain substrates such as glass or aluminium by creating chemical bonds between substrate and primer.

Bluesil™ 2-component silicone casting compounds

For all areas of mold making where highly flexible molding compounds have to be used.

Bluesil™ 2-component silicones

2-component silicone casting compounds, optically clear or containing filler for higher heat dissipation.

Bluesil™ Silicone gels

2-component silicones with gel-like end properties, extremely low hardness and extremely low elasticity modulus, optically clear.

Cinquasia® Organic pigment powder

Organic pigments with excellent light fastness and high chemical and solvent resistance.

Euromelt® 2-component polyamide hotmelt casting compounds

1-component co-polyamides for a wide operating temperature range and low viscosity for very good flow behavior with only low potting pressure.

Euvinyl® Pigments in PVC carrier

Irgafos additives are secondary antioxidants that act as peroxy radical scavengers during plastics processing.

Glacier Mica-based interference pigments

Titanium-coated synthetic mica for producing white sparkling effects with bluish frost character.

Heliogen® Organic pigment powder

Organic pigments with excellent light fastness and high chemical and solvent resistance.

Irgaclear® Clarifier nucleating agents

Characterized in particular in the application in polypropylene, by the transparency of the polymer is significantly increased.

Irgafos® Phosphite process stabilizers

Irgafos additives are secondary antioxidants that act as peroxy radical scavengers during plastics processing.

Irgalite® Organic pigment powder

Organic pigments with excellent light fastness and high chemical and solvent resistance.

Irgazin® Organic pigment powder

Organic pigments with excellent light fastness and high chemical and solvent resistance.

L&L Acoustic Sealants

L&L Acoustic Sealants are used as self-adhesive inflation tapes in automotive engineering to prevent the transmission of sound into the vehicle interior. Heat-activated, these foam up, show different expansion, density and cell structures and completely seal off cavities.

L&L Core Splice Adhesives

Expanding adhesive mats used in composite sandwich structures. For bonding honeycomb joints and edge formation on GRP/CFRP pressed parts. Mats can be cut to size and expand thermally in ovens, presses or autoclaves. Low density.

L&L Heat activated sealants

L&L Heat activated sealants are applied as self-adhesive inflatable tapes into body cavities (A/B/C columns, roof frames etc.), expand these by heat activation, e.g. in the KTL process, and seal these completely against the penetration of moisture, air and dust.

L&L Hybrid sealants

Primerless UV-stable adhesive and sealing systems on hybrid basis with strong adhesion to metal, composites, thermoplastics with a broad mechanical spectrum.

L&L Room Temperature curing MMA Adhesives

Structural 2-component, methacrylate-based adhesives. Broad adhesion spectrum on different substrates. High strengths, fast curing times and elongation at break up to 70%.

L&L Room temperature curing sealant/adhesives

Elastic 1K sealants based on MS polymer and elastic 2K adhesives with various mechanical properties. Direct adhesion to a variety of materials without pre-treatment.

L&L Seal 1-component silane-modified polymer adhesives

Primerless systems with good adhesion to metals, composites and plastics. Solvent- and isocyanate-free, with good UV resistance and low shrinkage for low marking.

L&L structural adhesive films

Self-adhesive EP adhesive strips, activated by heat, typically used in body-in-white construction. Different expansion rates enable bridging of gaps, compensation of thermal expansion and galvanic separation of substrates. Reinforcement of flat components.

L&L Structural adhesive tapes


Lumina® Mica-based interference pigments

Titanium-coated synthetic mica for producing white sparkling effects with bluish frost character.

MagnaPearl® Pearlescence pigments

Pearlescence pigments based on oxide-coated natural mica. Different particle sizes and oxide layer thicknesses give the pigments the different semi-transparent sparkling effects in different metallic and colored shades.

Multiaxial carbon fabrics

Very flat, non-crimp fabrics from 100gsm with 2 layers and up to 1600gsm with a maximum of 9 layers, can be produced in widths up to 2540mm (100 inches).

PACTAN 1-component silicone adhesives and sealants

Room temperature crosslinking adhesives and sealants for the encapsulation of electronic assemblies, for the bonding of cooker components (FDA-approved), engine components with high temperature loads, car headlights and for showcase construction.

Pactan® 1-component silicones

Neutral-curing 1-component silicones with very good adhesion properties for potting and sealing electrical components.

PACTAN 2-component silicone adhesives and sealants

Due to the cross-linking by installation of released water from the B-component, large adhesive layer thicknesses and a high hardening speed can be achieved. Suitable for flexible glass-to-metal bonding and showcase construction, partly specially designed for the production of foam seals, e.g. for household appliances, electrical and electronic housings.

Paliogen® Organic pigment powder

Organic pigments with excellent light fastness and high chemical and solvent resistance.

Permabond® Anaerobic adhesives

1-component, solvent-free systems that harden in the absence of atmospheric oxygen and the presence of metal surfaces (ferrous and non-ferrous metals). The liquid anaerobic adhesive fills the gap between the contact surfaces and hardens to a solid acrylic.

Recycled carbon fabrics

Fabrics contain reclaimed carbon fibre, resulting in products that are sustainable and cost effective.

RenCast® 2-component epoxy casting resins

For the production of high-precision castings in model and mold making. Products with excellent resistance to high temperatures are available.

RenCast® 2-component polyurethane fast casting resins

For the production of control or auxiliary castings in model and mold making.

RenGel™ Epoxy gelcoats and coupling layers

For all applications in model and mold making, specially adapted to temperature requirements, abrasion resistance, grindability, polishability and high chemical resistance.

RenLam® Laminating resins

Epoxy laminating resins with focus on mould and tool making.

RenLease® Release agents

For easy demolding of components made of polyurethane or epoxy resins.

RenPim™ 2-component polyurethane casting resins

For component production in rapid prototyping. Suitable for vacuum casting.

Rhodorsil® 2-component silicone casting compounds

For all areas of mold making where highly flexible molding compounds have to be used.

RickoStab Multi-component additive packages

The combination of several additives, e.g. primary and secondary antioxidants, HALS and UV absorbers facilitate dosage during processing.

Thermally conductive silicones

2-component silicone casting compounds, gels and gap fillers with excellent thermal conductivity.

Undirectional carbon fabrics

Fabrics have carbon fibres just in one direction.

UREOL® Adhesives for epoxy tooling boards

Color, density, coefficient of thermal expansion and glass transition point are specially matched to the mechanical properties of Ureol epoxy resin boards.

UREOL® Adhesives for polyurethane tooling boards

Color, density, coefficient of thermal expansion and glass transition point are specially matched to the mechanical properties of Ureol polyurethane boards.

UREOL® Epoxy tooling boards

Optimally matched to the requirements of composite mold making. Particularly suitable for all mold making applications in the temperature range up to 140°C, especially for prepreg laying tools.

Wax sheets

For the simulation of the component wall thickness in mould construction.

Events

JEC World 2020

03.03.2020, Paris

Bonding Seminar 2020

14.05.2020, Augsburg

News

The specialty chemicals expert distributes innovative Loctite products for electrical and electronics applications

Comprehensive ISO-certified production with growing capacity for epoxy resins, polyurethanes and packaging fillers